Our Products > Vulcanizers for Rubber Conveyor Belts > Repair > Repce Repce Repce Spot repair press. - Available for up to 1600mm wide belts. - Removable platens for easier handling - Automatic control unit. - Water cooled. Request a Quote Technical Data Further info Accessories Photos Videos Downloads MaterialAluminiumHeatingHeating Elements - 185º C (365º F) Max.PressurePressure bag (Air/Water) - 5 Bar (75 PSI)CoolingWaterRepairable areaUp to 350x300mm Millimeters Inches Model G1 (mm) (in)GCP (mm) (in)G3 (mm) (in)A (mm) (in)B (mm) (in)L (mm) (in)Total weight (Kg) (Lb) Repce 1400175 mm98 mm680 mm300 mm350 mm1217 mm74 KgRepce 1600175 mm98 mm700 mm300 mm350 mm1317 mm81 Kg Repce 14006.89 in3.86 in26.77 in11.81 in13.78 in47.91 in162.80 LbRepce 16006.89 in3.86 in27.56 in11.81 in13.78 in51.85 in178.20 Lb The technical data shown are subject to change without notice. Description Spot repair press. Aluminium made. Available for several belt widths up to 1400mm (superior dimensions under request). The vulcanizer includes pneumatic pressure system, heating system and cooling system. The vulcanizing area is composed by 2 heating platens that hold the heating elements, the temperature probes and the cooling pipes. Quickly removable to make handling easier. Completely automatic process programmed from the control unit (heating, dwell time and cooling). Controllers Easy programming. Automatic control of the whole splicing process, once the melting temperature, the dwell time and the cooling temperature have been set. Incorporates one thermometer and one ammeter per section. The ammeter allows the identification of possible problems in the electrical system of the vulcanizer, besides a voltmeter for input voltage reading that allows to detect any problem in the power supply. Automatic end-of-cycle buzzer. Pressure System The pressure is applied to the belt by means of a pressure bag (air/water), of the same dimensions of the heating platens. Maximum pressure 5 bar (75PSI). Heating System Fast heating of the platens (300x300mm) by means of heating elements. Each one is made with an asymmetrical winding to supply an even heat distribution all along the belt. The elements get warmer on the ends to compensate the loss of temperature and avoid heat concentration in the middle. Temperature programable up to 200º C / 392º F. Cooling system Water cooling system composed by a closed stainless steel circuit, that help circulate water all along the platens propelled by a water pump. Water favours a rapid temperature reduction of the belt and reduces waiting time for a new use of the press. Cooling system activates automatically after dwell time finishes. No videos currently available Available Documents Catalogue View PDF Spec Sheet View PDF Included Optional Repce control unitEasy to program control unit. Automatic control of the...Further infoEasy to program control unit. Automatic control of the whole splicing process once the melting temperature of both platens, the dwell time, the cooling temperature and the pressure have been set. The control box features an Automatic Temperature Regulation System (ATRS), that monitors automatically the differences of temperature between the heating platens during heating and dwell time. By doing so, differences of more than 2ºC are avoided. Includes voltmeter for input voltage reading that allows to detect any problem in the power supply. Includes also a pressure regulator, manometer and pneumatic valve with quick inflation and deflation. Automatic end-of-cycle buzzer. Cooling PumpSubmersible Pump, for the cooling of the heating...Further infoSubmersible Pump, for the cooling of the heating platens (water tank not included). 10 Bar Compressor10 Bar Piston Compressor of small size, with...Further info10 Bar Piston Compressor of small size, with monobloc head, heat protector, fit coupling and pressure reducer.