Repla

Repla - Vulcanizers for Rubber Conveyor Belts - Repair

Repla

Portable press for edge repair.

  • - Aluminium frame for the lowest possible weight.
  • - Wide section FONMAR pressure bag.
  • - Fully automatic control unit.
  • - Water cooled.

Request a Quote
  • Technical Data
  • Further info
  • Accessories
  • Photos
  • Videos
  • Downloads
MaterialAluminium
Heating185º C (365º F) Max.
PressurePressure bag - 7 Bar (100PSI)
CoolingWater
Repairable area1400x200mm | 1000x300mm

Metric Measurements Imperial Measurements

Model G1 (mm) (in)GS (mm) (in)G3 (mm) (in)A (mm) (in)B (mm) (in)D (mm) (in)L (mm) (in)Total weight (Kg) (Lb)
Repla 1400x200229 mm15 mm442 mm1400 mm200 mm382 mm1398 mm97 Kg
Repla 1000x300277 mm27 mm551 mm1000 mm300 mm502 mm900 mm106 Kg
Repla 1400x2009.02 in0.59 in17.40 in55.12 in7.87 in15.04 in55.04 in213.40 Lb
Repla 1000x30010.91 in1.06 in21.69 in39.37 in11.81 in19.76 in35.43 in233.20 Lb

The technical data shown are subject to change without notice.

Description

Press for edge repair. Aluminium made. Available in different platen dimensions (check availability). Completely automatic process programmed from the control unit (heating, dwell time and cooling).

Controllers

Easy to program control unit. Automatic control of the whole splicing process once the melting temperature of both platens, the dwell time, the cooling temperature and the pressure have been set. The control box features an Automatic Temperature Regulation System (ATRS), that monitors automatically the differences of temperature between the heating platens during heating and dwell time. By doing so, differences of more than 2ºC are avoided. Includes voltmeter for input voltage reading that allows to detect any problem in the power supply. Includes also a pressure regulator, manometer and pneumatic valve with quick inflation and deflation. Automatic end-of-cycle buzzer.

Pressure System

The pressure is applied to the belt by means of a pressure bag. 7 bar (100PSI) maximum pressure.

Heating system

Fast heating of the platens by means of heating elements. Each one is made with an asymmetrical winding to supply an even heat distribution all along the belt. The elements get warmer on the ends to compensate the loss of temperature and avoid heat concentration in the middle. Temperature programable up to 200º C / 392º F.

Cooling System              

Water cooling system composed by a closed stainless steel circuit, that help circulate water all along the platens propelled by a water pump. Water favours a rapid temperature reduction of the belt and reduces waiting time for a new use of the press. Cooling system activates automatically after dwell time finishes.

Repla - Vulcanizers for Rubber Conveyor Belts - Repair
Repla - Vulcanizers for Rubber Conveyor Belts - Repair
Repla - Vulcanizers for Rubber Conveyor Belts - Repair

No videos currently available

Available Documents
Spec Sheet   View PDF
Catalogue   View PDF
Included    
Optional
Repla control unit

Repla control unit

Easy to program control unit. Automatic control of the...

Further info

Cooling Pump

Cooling Pump

Submersible Pump, for the cooling of the heating...

Further info

10 Bar Compressor

10 Bar Compressor

10 Bar Piston Compressor of small size, with...

Further info

Understood

Our site uses cookies to provide you with a better service. If you continue to browse, it shall be deemed that you accept them. You can change the settings or obtain further information Here.

Send us your inquiry and we will contact you as soon as possible.

Name *
Country *
Email *
Phone Number
Message *
Send Close

Please, complete all the required fields *

The e-mail address supplied is not correct.

Contactar