Beta

Designed to manufacture rubber parts and for gluing profiles and blocks

- Hydraulic pressure by means of cylinders on the lower part.

- Adjustable working height for an easy placement of the moulds.

- Ongoing works without breaks.

- Easy handling by one single operator.

- Automatic lifting system.

Request a Quote

Technical Data
Further info
Accessories
Photos
Videos
Downloads

Material	Steel
Heating	Heating Elements - 200º C (392º F) Max.
Pressure	Hydraulic cylinders - 12 Bar (170PSI) Max.
Cooling	Water
Belt Width	Up to 2000mm (78,7")
Platen Length	500 - 750mm - 1000mm (19,6" – 23,6" – 39,3")
Angle	90º

Metric Measurements Imperial Measurements

Model	Belt (mm) (in)	G1 (mm) (in)	G3 (mm) (in)	A (mm) (in)	B (mm) (in)	L (mm) (in)
Beta 2000x1000	2000 mm	1100 mm	2260 mm	2160 mm	1000 mm	2900 mm
Beta 1800x1000	1800 mm	1100 mm	2260 mm	1960 mm	1000 mm	2700 mm
Beta 1600x1000	1600 mm	1100 mm	2260 mm	1760 mm	1000 mm	2500 mm
Beta 1400x1000	1400 mm	1100 mm	2260 mm	1560 mm	1000 mm	2300 mm
Beta 2000x750	2000 mm	1100 mm	2260 mm	2160 mm	750 mm	2900 mm
Beta 1800x750	1800 mm	1100 mm	2260 mm	1960 mm	750 mm	2700 mm
Beta 1600x750	1600 mm	1100 mm	2260 mm	1760 mm	750 mm	2500 mm
Beta 1400x750	1400 mm	1100 mm	2260 mm	1560 mm	750 mm	2300 mm
Beta 2000x1000	78.74 in	43.31 in	88.98 in	85,03 in	39,37 in	114.17 in
Beta 1800x1000	70.87 in	43.31 in	88.98 in	77,16 in	39,37 in	106.30 in
Beta 1600x1000	62.99 in	43.31 in	88.98 in	69,29 in	39,37 in	98.43 in
Beta 1400x1000	55.12 in	43.31 in	88.98 in	61,41 in	39,37 in	90.55 in
Beta 2000x750	78.74 in	43.31 in	88.98 in	85,03 in	29,52 in	114.17 in
Beta 1800x750	70.87 in	43.31 in	88.98 in	77,16 in	29,52 in	106.30 in
Beta 1600x750	62.99 in	43.31 in	88.98 in	69,29 in	29,52 in	98.43 in
Beta 1400x750	55.12 in	43.31 in	88.98 in	61,41 in	29,52 in	90.55 in

The technical data shown are subject to change without notice.

Description

Steel made workshop press. Available for different belt widths: from 10000mm up to 2200mm. The vulcanizer includes hydraulic pressure system, heating system and cooling system. Composed by 2 parts, top and bottom, both include the heating platens, cooling system and the temperature probes. Lengths of platen available: 500mm, 29”, 39” & 1200mm (20”, 24” y 47”). Completely automatic process programmed from the control unit (heating, dwell time and cooling).

Lifting System

The bottom platen is lifted up or lowered from the operator control desk. Incorporates a safety system for the blockage of the oil supply if the bolts are not properly placed.

The height of the work space may be adjustable in 3 planes (from 0 to 70mm, from 71mm to 190mm and from 191mm to 310mm), depending on the moulds to use.

Controllers

Easy programming operator control desk. Automatic control of the whole splicing process once the melting temperature of both platens, the dwell time, the cooling temperature and the pressure have been set. Also includes voltmeter for input voltage reading that allows to detect any problem in the power supply, ammeters, pressure regulator and manometer. Automatic end-of-cycle buzzer.

Pressure system

Adjustable and applied by means of hydraulic cylinders connected in series, built in the lower section and from high quality materials. The pressure is supplied to the cylinders by means of a hydraulic kit that automatically regulates the pressure (it recovers the pressure when it lowers and the opposite. Maximum pressure is 14 Bar (200PSI)

Heating System

Fast heating of the platens by means of heating elements. Each one is made with an asymmetrical winding to supply an even heat distribution all along the belt. The elements get warmer on the ends to compensate the loss of temperature and avoid heat concentration in the middle. Temperature programable up to 200º C / 392º F.

Cooling System

Water cooling system composed by a closed stainless steel circuit, that help circulate water all along the platens propelled by a water pump. Water favours a rapid temperature reduction of the belt and reduces waiting time for a new use of the press. Cooling and blowing systems (to remove all the water inside the platens) activates automatically after dwell time finishes.

Clamping System (option)

Fixing the belt by means of automatic clamping bars.

Bolts

Easily adjustable to different belt thicknesses. Steel made with safety factor 2 (capable of withstanding twice the maximum load pressure of the press).